Loading
RC parts
The part you need. Made for your model.
Replacement, upgrade and custom RC parts, designed and produced in Italy — for a better fit on the bench and a better run on the trail.
What we make for RC projects
Custom and replacement parts for RC models, from a one-off fix to a short run for a club. Functional, made to fit your model and the way you drive it.
Start your part request- Replacement partsDiscontinued or broken parts, redrawn to fit your model.
- Custom mounts and bracketsFor electronics, accessories and set-ups nobody sells.
- Scale accessoriesRealistic details that finish the build.
- Body detailsCustom trims, interior pieces and exterior elements.
- Workshop aidsJigs, stands and holders for building and maintenance.
- Prototype partsTest an idea on the chassis before you commit to it.
- Short-run batchesThe same part for a team, a club or a small series.
- UpgradesA stronger or better-placed version of a stock part.
How an RC part project works
A clear path from a broken part or an idea to a finished component.
Show us the part or the problem
Photos, measurements or the broken part. Tell us the model and what it has to do.
Define fit and use
We agree the requirements, the critical dimensions, the material and the finish.
Prototype and test
Where fit matters, a first piece goes on your model before anything else is made.
Approve and produce
Once it fits, we produce the final part, or the batch, to the agreed specification.
Typical requests
The kinds of RC part people bring us most often. Pick the closest one to start.
Built around fit, not guesswork.
Every part starts from your model and how you use it. We work from the original part, careful measurements or your own files, and where fit matters we check it on a first piece before anything else is made.
Start your part request
Materials, and what they can do
We choose the material and the way the part is made for the job it does: the load, the heat, the wear and the detail it needs. And we will tell you plainly when a part should stay metal.
- Strength and loadParts sized for the loads they actually carry.
- HeatMaterials chosen for what sits next to the motor and ESC.
- Wear and impactsPolymers that flex rather than shatter on a hard landing.
- Detail and finishFrom purely functional to scale-accurate.
- FitCritical dimensions measured on the finished part, not assumed.
- QuantityFrom a single part to a small batch.
We produce in polymer only. Screws, bearings and other hardware are bought in and fitted, and parts that carry real metal loads — gears, driveshafts, axles — are better left in metal. We will say so if that is your part.
Tell us about the part
The more you can share, the easier it is for us to understand what you need and suggest the right way to make it.
What helps us get started
- Your RC model and scaleBrand, model and scale — 1/10, 1/8, 1/24.
- Photos of the part or where it goesClear photos from several angles, even if it is broken.
- MeasurementsKey dimensions, or the original part if you still have it.
- How you use itTrail, crawling, bashing, racing or display.
- Any files you haveSTL, STEP or drawings are welcome.
Your project
Start with the thing itself. Rough is fine — describe it, say it out loud, or show us a photo.
A few lines is enough. Describe the problem if the piece is not clear yet.
0 of 1200
Voice note(optional)
Often the fastest way to explain an idea. Stored privately and never published.
Recording stops automatically after 3 minutes.
Photos, sketches or files(optional)
Drag files here, or
Images, PDFs and 3D files. Up to 4 files, 4 MB each.
When it has to exist
A real date changes what we can promise, so it is worth answering honestly.
How many?
How to reply
We normally reply within Within 24 hours.
Parts we design and produce are made in polymer. Glass, metal, candles, electronics and hardware can be built into a piece as purchased components.
Common questions
Can you reproduce a broken part?
Usually, yes. Send the pieces, or photos of them with a ruler in frame. Where the original broke because a wall was too thin, we will suggest making that area stronger rather than copying the weakness.
Do you need the original part?
It helps, but it is not essential. Photos with a ruler, a few key measurements or a part number for your model are often enough to start, and we will tell you if anything else is needed.
Can you work from STL or CAD files?
Yes. We check STL, STEP, OBJ and 3MF files for wall thickness, clearances and orientation before anything is produced, and tell you if a change is needed.
Is every RC part suitable for printing?
No. Gears, driveshafts, axles and anything else that carries real metal loads are better left in metal, and we will say so. Mounts, trays, brackets, bodywork details and many suspension and chassis parts are a good fit.
Can you make just one part?
Yes, a single part is the most common request. The model is kept, so a second one can be made later without starting again.
How long does it take?
It depends on whether the part has to be drawn, how many fitting rounds it needs and the quantity. You get a production window with the quote, before anything is made.
Do you ship outside Italy?
Yes. Delivery abroad is confirmed by email before you pay, and for countries outside the EU any import duty is paid on arrival.